Search Results

One of the most common applications of planetary (epi-cyclic) gear sets is found in automotive transmissions. A planetary gear set typically total torque applied to be shared by multiple planets making a higher power density possible. This advantage of the planetary gear sets relies heavily on the assumption that each pinion carries an equal share of the total torque applied. However, in production, gear manufacturing and assembly variations along with certain design parameters may prevent equal load sharing among the planets. Here, a generalized mathematical model of a single-stage planetary gear set having n planets is developed to predict load shared by each planet under quasi-static conditions. The model takes into account effects of two most common errors including pinion carrier errors and gear run-out errors. Results of an experimental test program are used to validate the predictions of the model. Generalized guidelines for equal load sharing are also presented.

This paper discusses a study conducted by GM to better understand the factors that influence injury potential in vehicle-to-vehicle side impacts. A number of other studies have been done which focus primarily on frontal vehicle-to-vehicle compatibility. GM focused on side impact compatibility in this study due to the risk of harm generally associated with this type of crash. Real world field performance was studied through an extensive six-state field analysis of recent model year (‘94+) vehicles. Of particular interest in this study was an efficacy analysis of the MVSS 214 dynamic side impact standard, which was phased-in starting with some 1994 model year passenger cars. Physical side impact crash testing of a 1997 passenger car was used to investigate the relationship of impacting mass, speed, geometric profile and stiffness on side impact intrusion and occupant injury.

The effects of strain-rate and element mesh size on the numerical simulation of an automotive component impacted by a mass dropped from an instrumented drop tower was investigated. For this study, an analysis of a simple steel rail hat-section impacted by a mass moving at an initial velocity of 28Mph was performed using the explicit finite element code Radioss. Three constitutive material models: Elasto-Plastic (without strain rate), Johnson-Cook, and Zerilli-Armstrong were used to characterize the material properties for mild and high strength steel. Results obtained from the numerical analyses were compared to the experimental data for the maximum crush, final deformation shape, average crush force and the force-deflection curve. The results from this study indicate that the mechanical response of steel can be captured utilizing a constitutive material model which accounts for strain rate effect coupled with an average mesh size of 6 to 9mm.

This paper presents an innovative automobile application of Computational Fluid Dynamics (CFD) as a complement to wind tunnel experimentation for the evaluation of rain water and wiper wash flow on the exterior of a moving vehicle. In addition to calculating the air flow around a car, a multi-phase CFD code was used to simulate rain drops in the air stream, rain drops impinging on the vehicle, and the transport of the “thin liquid film” of water on the vehicle surfaces. Time-dependent results for the location, velocity, and height of the water film on the windshield, A-pillar, and side glass were obtained. The CFD results compared favorably with a wind tunnel procedure. The variation of the calculated water film corresponded with observed patterns of water streaks on test vehicles. Design iterations performed on the computational model also agreed with similar test configurations.

The new regulations to reduce emissions have resulted in the development of new techniques to maintain or enhance competitive performance. A requirement for the manifold is to help meet the reduction in cold start emissions, particularly during the transient conditions from start to 100 seconds following the Federal Test Procedures for vehicle emissions. Finite element computer models were developed to predict inner and outer wall temperatures, and to determine structural soundness. Tests were performed to assure that noise levels were minimized. Dynamometer lab and field tests were performed to verify that the manifold would meet the design requirements. From the results of these tests and analyses, modifications were made to the weld and manufacturing techniques to improve product life and reduce noise. Dual wall manifolds have proven durability to meet high exhaust gas temperatures up to 1650°F (900°C), while meeting the performance, noise, and weight reduction goals.

Over the past 20 years, polyvinyl chloride (PVC) has almost replaced metal in stationary glass reveal moldings with dramatic part cost savings on cars and trucks world-wide. The process of assembly is generally simple and convenient but to replace a reveal molding can be difficult. Many times, in order to replace the molding, it may also be necessary to replace or reseal the glass. In short, PVC reveal moldings, relatively inexpensive parts, are very expensive to service. Outside of general assembly and processing issues, there are 5 variables that may cause a failure in the performance of a stationary glass reveal molding. They are as follows: material degradation, crystallization, plasticizer loss, material properties, and molded-in stress. Because of modern standard PVC formulations and the material requirements of most automotive companies, material degradation, crystallization and plasticizer loss do not commonly cause failure. Material properties and molded-in stress do.

A method is presented to process random vibration data from a complete road durability test environment as stationary segments and then develop test profiles based on fatigue content of their power spectral densities. Background is provided on existing techniques for estimating fatigue damage in the frequency domain. A general model for stress response to acceleration is offered to address the vibration test's requirement for acceleration data and the fatigue prediction method's requirement for stress data. With these tools, the engineer can extend test correlation beyond failure modes to include retention of estimated fatigue damage. Recommendations allow for test time compression from editing and improve existing exaggeration methods.

General Motors Powertrain Group (GMPTG) has developed an all new small block V8 engine, designated LS1, for introduction into the 1997 Corvette. This engine was designed to meet both customer requirements and competitive challenges while also meeting the ever increasing legislated requirements of emissions and fuel economy. This 5.7L V8 provides increased power and torque while delivering higher fuel economy. In addition, improvements in both QRD and NVH characteristics were made while meeting packaging constraints and achieving significant mass reductions.

General Motors Powertrain Division has developed the next generation big block V8 engine for introduction in the 1996 model year. In addition to meeting tighter emission and on-board diagnostic legislation, this engine evolved to meet both customer requirements and competitive challenges. Starting with the proven dependability of the time tested big block V8, goals were set to substantially increase the power, torque, fuel economy and overall pleaseability of GM's large load capacity gasoline engine. The need for this new engine to meet packaging requirements in many vehicle platforms, both truck and OEM, as well as a requirement for minimal additional heat rejection over the engine being replaced, placed additional constraints on the design.

This paper presents a model updating method based on experimental receptances. The presented method minimises the so called ‘indirect receptance difference’. First, the reduced analytical dynamic stiffness matrix is expressed as an approximate, linearised function of the updating parameters. In a numerically stable, iterative procedure, this reduced analytical dynamic stiffness matrix is changed in such a way that the analytical receptances match the experimental receptances at the updating frequencies. The updating frequencies are a set of selected frequency points in the frequency range of interest. Some considerations about an optimal selection of the updating frequencies are given. Finally, a mixed static-dynamic reduction scheme is discussed. Dynamic reduction of the analytical dynamic stiffness matrix at each updating frequency is physically exact, but it involves a great computational effort.

Optimal design changes to solve vibration induced fatigue failures can only be derived by including structural dynamics considerations into the fatigue lifetime calculation process. Such an integrated design approach to resonance fatigue problems has been developed within the EC Esprit Project 2486 DYNAMO. Also an integration of crack initiation and crack growth calculations has been realised. This integrated dynamic analysis/fatigue analysis procedure is demonstrated in the paper by means of a resonance fatigue problem of a car.

“Noise and vibration are not invented here!”. Undesirable structural dynamic behaviour is normally experienced on final assemblies, by which time the underlying cause of the problem is difficult to solve intuitively. Solving the problems classically involves the partial breakdown of assemblies and the application of various structural dynamics testing and analysis procedures. Preferably, noise and vibration problems should be avoided by designing the product right the first time, by the use of various integrated analysis and testing disciplines, from the component level to the final assembly. Such an approach is referred to, in a broader sense, by trendy themes as concurrent engineering, forward engineering, simultaneous engineering.... This paper analyzes trends in analytical and experimental structural dynamics toward better integration of the various discipline oriented techniques that are currently used.

An automated engine dynamometer test procedure is developed and mathematical models for the main engine control variables are derived from the resulting data base. The new procedure involves sequential testing at many speed/load conditions for various combinations of air fuel ratio, spark timing and exhaust gas recirculation. The total testing time required for generating the data base of more than 2000 test points is less than twelve hours. An independent transient speed/load test is also conducted for the purpose of validating the engine models. The measured and model predicted data are compared for this test which corresponds to a segment of the EPA urban schedule.

The Experimental Safety Vehicle powertrain and fuel system developed by General Motors in compliance with Contract DOT-OS-00095 with the U.S. Department of Transportation include several special features: a low engine accessory package to meet the front visibility down angle of 8 degrees, engine and transmission mounting for retention at high decelerations, a light aluminum engine, an over-the-rear-axle fuel tank, and a unique evaporative emission fuel pipe routing. A comprehensive test program was planned and final testing to validate contract specifications was conducted.

A comprehensive cycle analysis has been developed for four-stroke spark-ignited engines from which the indicated performance of a single cylinder engine was computed with a reasonable degree of accuracy. The step-wise cycle calculations were made using a digital computer. This analysis took into account mixture composition, dissociation, combustion chamber shape (including spark plug location), flame propagation, heat transfer, piston motion, engine speed, spark advance, manifold pressure and temperature, and exhaust pressure. A correlation between the calculated and experimental performance is reported for one engine at a particular operating point. The calculated pressure-time diagram was in good agreement with the experimental one in many respects. The calculated peak pressure was 10 per cent lower and the thermal efficiency 0.8 per cent higher than the measured values. Thus this calculational procedure represents a significant improvement over constant volume cycle approximations.